Security Policy 01.02.11 RSA BSAFE® Crypto-J JSAFE and JCE Software Module 5.0 Security Policy Level 1 Roles, Authentication and Services This document is a non-proprietary security policy for RSA BSAFE Crypto-J JSAFE and JCE Software Module 5.0 (Crypto-J) security software. This document may be freely reproduced and distributed whole and intact including the copyright notice. Contents: Preface ............................................................................................................ 2 References .............................................................................................. 2 Terminology ............................................................................................. 2 Document Organization ......................................................................... 3 1 Crypto-J Cryptographic Toolkit ................................................................... 4 1.1 Introduction ......................................................................................... 4 1.2 Toolkit Characteristics ....................................................................... 5 1.3 Toolkit Interfaces ................................................................................ 7 1.4 Roles and Services ........................................................................... 8 1.5 Cryptographic Key Management ................................................... 12 1.6 Cryptographic Algorithms ............................................................... 15 1.7 Self-tests ........................................................................................... 17 2 Secure Operation of Crypto-J .................................................................. 19 2.1 Module Configuration ...................................................................... 19 2.2 Security Roles, Authentication, and Services Operation ........... 19 2.3 Crypto User Guidance .................................................................... 20 2.4 Crypto Officer Guidance ................................................................. 23 2.5 Role Changes .................................................................................. 23 2.6 Operating the Cryptographic Module ............................................ 23 2.7 Modes of Operation ......................................................................... 24 2.8 Random Number Generator .......................................................... 25 3 Acronyms .................................................................................................... 26 1 February 2011 Copyright © 2011 EMC Corporation. All rights reserved. 1 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Preface This document is a non-proprietary security policy for the Crypto-J cryptographic toolkit from RSA, the Security Division of EMC (RSA). This security policy describes how the Crypto-J toolkit meets the Level 1 FIPS 140-2 Security Level 1 validation of the Crypto-J toolkit. Crypto-J provides both the JSAFE and JCE Application Programming Interfaces (APIs), in the cryptojFIPS.jar file. All references to the Crypto-J toolkit apply to both interfaces unless explicitly noted. FIPS 140-2 (Federal Information Processing Standards Publication 140-2 - Security Requirements for Cryptographic Modules) details the U.S. Government requirements for cryptographic modules. More information about the FIPS 140-2 standard and validation program is available on the NIST website. References This document deals only with operations and capabilities of the Crypto-J in the technical terms of a FIPS 140-2 cryptographic toolkit security policy. More information on Crypto-J and the entire RSA BSAFE product line is available at: • http://www.rsa.com/, for information on the full line of products and services. • http://www.rsa.com/node.aspx?id=1319 for an overview of security tools for Java developers. • http://www.rsa.com/node.aspx?id=1204 for an overview of the RSA BSAFE product range. Terminology In this document, the term Crypto-J Module denotes the Crypto-J 140-2 Security Level 1 validated Cryptographic Module. The Crypto-J Module is also referred to as: • The Cryptographic Module • The module. 2 Preface RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Document Organization This Security Policy document is one document in the 140-2 Security Level 1 Validation Submission package. With the exception of the Non-Proprietary Crypto-J Security Policy, the 140-2 Security Level 1 Validation Submission Documentation is RSA Security-proprietary and is releasable only under appropriate non-disclosure agreements. For access to the documentation, please contact RSA Security. This document explains the Crypto-J features and functionality relevant to FIPS 140-2, and contains the following sections: • This section, “Preface” on page 2 provides an overview and introduction to the Security Policy. • “Crypto-J Cryptographic Toolkit” on page 4, describes Crypto-J and how it meets the 140-2 Security Level 1 requirements. • “Secure Operation of Crypto-J” on page 19, addresses the required configuration for the FIPS140-mode of operation. • “Acronyms” on page 26, lists the definitions for the acronyms used in this document. Preface 3 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1 Crypto-J Cryptographic Toolkit This section provides an overview of the Crypto-J toolkit, and contains the following topics: • Introduction • Toolkit Characteristics • Toolkit Interfaces • Roles and Services • Cryptographic Key Management • Cryptographic Algorithms • Self-tests. 1.1 Introduction More than a billion copies of the RSA BSAFE technology are embedded in today's most popular software applications and hardware devices. Encompassing the most widely-used and rich set of cryptographic algorithms as well as secure communications protocols, RSA BSAFE software is a set of complementary security products relied on by developers and manufacturers worldwide. The Crypto-J software library is the world's most trusted Java-language cryptography component, and is at the heart of the RSA BSAFE product line. It includes a wide range of data encryption and signing algorithms, including AES, Triple-DES, RC5, the RSA Public Key Cryptosystem, the Elliptic Curve Cryptosystem, the DSA government signature algorithm, and the SHA1 and SHA2 message digest routines. Its software libraries, sample code and complete standards-based implementation enable near-universal interoperability for your networked and e-business applications. Any programmer using the RSA BSAFE Crypto-J tools can easily create secure applications without a background in cryptography, mathematics or number theory. 4 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.2 Toolkit Characteristics Crypto-J is classified as a FIPS 140-2 multi-chip standalone module. As such, Crypto-J is tested on particular operating systems and computer platforms. The cryptographic boundary includes Crypto-J running on selected platforms that are running selected operating systems. Crypto-J is validated for FIPS 140-2 Security Level 1 requirements. Crypto-J is packaged in a Java Archive (JAR) file containing all the code for the toolkit. In addition, Crypto-J relies on the physical security provided by the host on which it runs. Both the JSAFE and JCE APIs of the Crypto-J toolkit are provided in the cryptojFIPS.jar file. Crypto-J is tested on the following platforms: • Microsoft Windows XP SP3 (32-bit) with Sun™ JRE™ 5.0 • Microsoft Windows XP SP3 (32-bit) with Sun JRE 6.0. Compliance is maintained on platforms for which the binary executable remains unchanged. This includes (but is not limited to): • Microsoft Windows 2000 Professional, SP4, Sun JRE 5.0/6.0, IBM® JRE 5.0 – – Windows XP SP2, Sun JRE 5.0/6.0, IBM JRE 5.0, JRockit 5.0/6.0 – Windows XP Professional (64-bit), Sun JRE 5.0/6.0 – Windows 2003 Server (32-bit), Sun JRE 5.0/6.0, IBM JRE 5.0, JRockit 5.0/6.0 – Windows 2003 Server (64-bit), Sun JRE 5.0/6.0, JRockit 5.0/6.0 – Windows 2008 Server (32-bit), Sun JRE 6.0 – Windows 2008 Server (64-bit), Sun JRE 6.0 Windows Vista® (32-bit), Sun JRE 5.0/6.0, IBM JRE 5.0, JRockit 5.0/6.0 – – Windows Vista (64-bit), Sun JRE 5.0/6.0, JRockit 5.0/6.0. • Sun – Solaris™ 9, UltraSparc v8+ (32-bit), Sun JRE 5.0/6.0, IBM JRE 5.0 – Solaris 9, UltraSparc v9 (64-bit), Sun JRE 5.0/6.0 – Solaris 10, UltraSparc v8+ (32-bit), Sun JRE 5.0/6.0, IBM JRE 5.0 – Solaris 10, UltraSparc v9 (64-bit), Sun JRE 5.0/6.0, IBM JRE 5.0, JRockit 5.0/6.0 – Solaris 10, x86 (64-bit), Sun JRE 5.0/6.0. Crypto-J Cryptographic Toolkit 5 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Linux® • Red Hat® Enterprise Linux AS 4.0, x86 (32-bit), Sun JRE 5.0/6.0, – IBM JRE 5.0, JRockit 5.0/6.0 – Red Hat Enterprise Linux AS 4.0, x86 (64-bit), Sun JRE 5.0/6.0, JRockit 5.0/6.0 – Red Hat Enterprise Linux AS 5.0, x86 (32-bit), Sun JRE 5.0/6.0, IBM JRE 5.0, JRockit 5.0/6.0 – Red Hat Enterprise Linux AS 5.0, x86 (64-bit), Sun JRE 5.0/6.0, JRockit 5.0/6.0 Novell® SUSE® Linux Enterprise Server 9, x86 (32-bit), Sun JRE 5.0/6.0 – – Novell SUSE Linux Enterprise Server 9, x86 (64-bit), Sun JRE 5.0/6.0 – Novell SUSE Linux Enterprise Server 10, x86 (32-bit), Sun JRE 5.0/6.0 – Novell SUSE Linux Enterprise Server 10, x86 (64-bit), Sun JRE 5.0/6.0. • HP – HP-UX 11.23, Itanium 2 (32-bit), HP JRE 5.0/6.0 – HP-UX 11.23, Itanium 2 (64-bit), HP JRE 5.0/6.0 – HP-UX 11.31, Itanium 2 (32-bit), HP JRE 5.0/6.0 – HP-UX 11.31, Itanium 2 (64-bit), HP JRE 5.0/6.0. • IBM AIX 5L™ v5.3, Power PC® (32-bit), IBM JRE 5.0/6.0 – – AIX 5L v5.3, Power PC (64-bit), IBM JRE 5.0/6.0 – AIX 5L v6.1, Power PC (32-bit), IBM JRE 5.0/6.0 – AIX 5L v6.1, Power PC (64-bit), IBM JRE 5.0/6.0. For a resolution on the issue of multi-user modes, see the NIST document Implementation Guidance for FIPS PUB 140-2 and the Cryptographic Module Validation Program. 6 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.3 Toolkit Interfaces As a multi-chip standalone toolkit, the physical interface to Crypto-J consists of a keyboard, mouse, monitor, serial ports and network adapters. The underlying logical interface to the toolkit is the API, documented in the RSA BSAFE Crypto-J Developer's Guide. The Crypto-J toolkit provides for Control Input through the API calls. Data Input and Output are provided in the variables passed with API calls, and Status Output is provided in the returns and error codes documented for each call. This is shown in the following diagram. Physical Boundary Application Data In Data O ut Control In Status O ut Cryptographic Boundary Cryptographic M odule cryptojFIPS.jar Runs on JVM Provides services for M odule Java Virtual M achine( JVM ) Provides services for Run on O S JVM Operating System (OS) Software Runs on Hardware Hardware Provides service for O S Hardware Figure 1 Crypto-J Logical Diagram Crypto-J Cryptographic Toolkit 7 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.4 Roles and Services Crypto-J meets all FIPS140-2 Level 1 requirements, implementing both a Crypto Officer role and a Crypto User role. As allowed by FIPS 140-2, Crypto-J does not require user identification or authentication for these roles. The API for control of Crypto-J is through the com.rsa.jsafe.crypto.CryptoJ class. The API is duplicated in the class com.rsa.jsafe.CryptoJ. 1.4.1 Crypto Officer Role An operator can assume the Crypto Officer Role by invoking the com.rsa.jsafe.crypto.CryptoJ.setRole() method with the CryptoJ.CRYPTO_OFFICER_ROLE argument. After this invocation, services available to the Crypto Officer Role can be used. An operator can also assume the Crypto Officer Role by constructing a FIPS140Context object where the role is specified as CryptoJ.CRYPTO_OFFICER_ROLE. The FIPS140Context object can then be input to a Service which is to be used by the Crypto Officer Role. The Services section provides a list of services available to the Crypto Officer Role. 1.4.2 Crypto User Role The Crypto User Role is the default operating role for the module. An operator can explicitly assume the Crypto User Role by invoking the com.rsa.jsafe.crypto.CryptoJ.setRole() method with the CryptoJ.USER_ROLE argument. Once the role is set to Crypto User Role, either by default or explicitly, services available to the Crypto User Role can be used. An operator can also assume the Crypto User Role by constructing a FIPS140Context object where the role is specified as CryptoJ.USER_ROLE.The FIPS140Context object can then be input to a Service which is to be used by the Crypto User Role. The Services section provides a list of services available to the Crypto User Role. 1.4.3 Services The following table lists the un-authenticated services provided by Crypto-J which may be used by either Role in terms of the toolkit interface. Table 1 Services Available to the Crypto User and Crypto Officer Roles Services Available to the Crypto User and Crypto Officer Roles CryptoJ.getFIPS140Context CryptoJ.getSeeder CryptoJ.setSeeder CryptoJ.getDefaultRandom 8 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 1 Services Available to the Crypto User and Crypto Officer Roles (continued) Services Available to the Crypto User and Crypto Officer Roles CryptoJ.isFIPS140Compliant CryptoJ.getState CryptoJ.getMode CryptoJ.setMode CryptoJ.getRole CryptoJ.setRole CryptoJ.disableLibrary CryptoJ.selfTestPassed CryptoJ.runSelfTests CryptoJ.isInFIPS140Mode CryptoJ.isInSSLMode CryptoJ.isInECCMode CryptoJ.notInFIPS140Mode CryptoJ.checkIntegrity CryptoJ.getFIPS140SecurityLevel CryptoJ.isFIPS140SecurityLevelOne CryptoJ.isFIPS140SecurityLevelTwo CryptoJ.getFIPS140ModuleName CryptoJ.fips186RandomClearQ CryptoJ.fips186RandomSetQ CryptoJ.verifyPQGParams AccessDescription AlgorithmParameterGenerator AlgorithmParameters ArchiveEncryptedKey ArchiveEncryptedKeyLegacy ArchiveFromParameters ArchiveGeneratedPrivKey ArchiveOptions Assurance Attribute AuthorityKeyIdentifier CCMParameterSpec CertComplianceAdjustment CertConfirmationMessage CertConfirmationMessageImpl CertCreationFactory CertCreationParameterSpec CertificateFactory CertJVersion CertPathBuilder CertPathValidator CertPathWithOCSPParameters CertRequest CertRequestFactory CertRequestMessage CertRequestMessageImpl CertTemplateSpec Cipher CMPController CMPServerConfig ControlsSpec CRLCreationFactory CRLCreationParameterSpec CRMFParameterSpec CRMFProofGenerationParams Crypto-J Cryptographic Toolkit 9 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 1 Services Available to the Crypto User and Crypto Officer Roles (continued) Services Available to the Crypto User and Crypto Officer Roles CryptoJVersion CryptoJVersion DistributionPoint DistributionPointName DRBGInstantiationParameterSpec DRBGOperationalParameterSpec DSAGenParameterSpec ECIESParameterSpec EncryptedValue EVChecker FIPS140Context GCMParameterSpec GeneralName GeneralSubtree HttpCMPServerConfig IssuerInformation IssuingDistributionPoint JSAFE_AsymmetricCipher JSAFE_Key JSAFE_KeyAgree JSAFE_KeyAttributes JSAFE_KeyPair JSAFE_KeyWrapCipher JSAFE_MAC JSAFE_MessageDigest JSAFE_Obfuscator JSAFE_Object JSAFE_Parameters JSAFE_PrivateKey JSAFE_PublicKey JSAFE_Recode JSAFE_SecretKey JSAFE_SecureRandom JSAFE_Session JSAFE_SessionSpec JSAFE_Signature JSAFE_SymmetricCipher JSAFE_VerifyPQG JsafeJCE KeyAgreement KeyFactory KeyGenerator KeyIdentifier KeyPairGenerator KeyStore LDAPCertStoreParameters Mac MACProtection MessageDigest MessageHeaderInfo MessageProtection ObjectID OCSP OCSPParameters OCSPResponderConfig OCSPWithRespondersParameters 10 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 1 Services Available to the Crypto User and Crypto Officer Roles (continued) Services Available to the Crypto User and Crypto Officer Roles OCSPWithResponseParameters PKCS10ParameterSpec PKCS10SigningParameters PolicyChecker POPEncryptedKey POPEncryptedKeyLegacy POPPrivateKeySpec POPRAVerifiedSpec POPSigningKeySpec POPSubsequentMessage ProofGenerationParameters ProofOfPossessionSpec PSSParameterSpec RegInfoSpec RevocationDetails RevocationRequestMessage RevocationRequestMessageImpl RevokedCertificate RSAGenParameterSpec RSAJCP SecureRandom SecureRandomEx SensitiveData Signature SignatureProtection StatusInfo SuiteBChecker TcpCMPServerConfig ValidateEncryptedKeyParams ValidateParameters ValidateSignKeyParams X500PrincipalBuilder X509CRLEntryExtensionSpec X509CRLExtensionSpec X509ExtensionRequestSpec X509ExtensionSpec X509V1BuilderParameters X509V1BuilderResult X509V1ValidatorParameters X509V1ValidatorResult X942DHParameterSpec X942DHPrivateKeySpec X942DHPublicKeySpec XTSParameterSpec For more information on each function, see the RSA BSAFE Crypto-J Developer's Guide. Crypto-J Cryptographic Toolkit 11 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.5 Cryptographic Key Management 1.5.1 Key Generation The Crypto-J toolkit supports the generation of the DSA, RSA, and Diffie-Hellman (DH) and ECC public and private keys. The toolkit also employs a Federal Information Processing Standard 186-2, Digital Signature Standard (FIPS 186-3) Approved Random Number Generator, a FIPS Approved HMAC Deterministic Random Bit Generator (HMAC DRBG SP800-90), as well as a FIPS Approved Dual Elliptic Curve Deterministic Random Bit Generator (ECDRBG SP 800-90) for generating asymmetric and symmetric keys used in algorithms such as AES, Triple-DES, RSA, DSA, DH and ECC. 1.5.2 Key Protection All key data resides in internally allocated data structures and can only be output using the Crypto-J API. The operating system and the Java Runtime Environment (JRE) safeguards memory and process space from unauthorized access. 1.5.3 Key Access An authorized operator of the module has access to all key data created during Crypto-J operation. Note: The User and Officer roles have equal and complete access to all keys. The following table lists the different services provided by the toolkit with the type of access to keys or CSPs. Table 2 Key and CSP Access Service Key or CSP Type of Access Encryption and decryption Symmetric keys (AES, Triple-DES) Read/Execute Digital signature and Asymmetric keys (DSA, RSA, ECDSA) Read/Execute verification Hashing None N/A MAC HMAC keys Read/Execute Random number generation FIPS 186-2 seed and key Read/Write/Execute X931Random seed and number of streams HMAC DRBG entropy, strength, and seed EC DRBG entropy, strength, and seed Key establishment primitives Asymmetric keys (RSA, DH, ECDH) Read/Execute 12 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 2 Key and CSP Access (continued) Service Key or CSP Type of Access Key generation Symmetric keys (AES, Triple-DES) Write Asymmetric keys (DSA, EC DSA, RSA, DH, ECDH) MAC keys (HMAC) Self-test Hard coded keys Read/Execute (AES, Triple-DES, RSA, DSA, ECDSA and HMAC) Show status None N/A Zeroization All Read/Write 1.5.4 Key Zeroization Users can ensure sensitive data is properly zeroized by making use of the SensitiveData.clear() method for clearing sensitive data. The toolkit ensures that all ephemeral sensitive data is cleared within the toolkit. For more information about clearing sensitive data, see Clearing Sensitive Data in the RSA BSAFE Crypto-J Developer's Guide. Crypto-J Cryptographic Toolkit 13 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.5.5 Key Storage Crypto-J does not provide long-term cryptographic key storage. Storage of keys is the responsibility of the user of Crypto-J. The following table shows how the storage of keys and Critical Security Parameters (CSPs) are handled. The Crypto User and Crypto Officer roles have equal and complete access to all keys and CSPs. Table 3 Key and CSP Storage Item Storage AES keys In volatile memory only (plaintext) Triple-DES keys In volatile memory only (plaintext) HMAC with SHA1 and SHA2 keys In volatile memory only (plaintext) EC public keys In volatile memory only (plaintext) EC private keys In volatile memory only (plaintext) DH public key In volatile memory only (plaintext) DH private key In volatile memory only (plaintext) RSA public key In volatile memory only (plaintext) RSA private key In volatile memory only (plaintext) DSA public key In volatile memory only (plaintext) DSA private key In volatile memory only (plaintext) PRNG seeds (FIPS 186-2) In volatile memory only (plaintext) PRNG Keys (FIPS 186-2) In volatile memory only (plaintext) EC DRBG Entropy In volatile memory only (plaintext) EC DRBG S Value In volatile memory only (plaintext) EC DRBG init_seed In volatile memory only (plaintext) HMAC DRBG Entropy In volatile memory only (plaintext) HMAC DRBG V Value In volatile memory only (plaintext) HMAC DRBG Key In volatile memory only (plaintext) HMAC DRBG init_seed In volatile memory only (plaintext) 14 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.6 Cryptographic Algorithms Crypto-J meets FIPS 140-2 requirements by implementing algorithm enforcement, such that when operating in FIPS140_MODE, only FIPS 140-approved algorithms are available for use. The following table lists the FIPS 140-approved algorithms provided by Crypto-J, when operating in FIPS140_MODE. Table 4 Crypto-J FIPS-approved Algorithms Algorithm Validation Certificate AES ECB, CBC, CFB (128), OFB (128), Certificate #1465 CTR - [128, 192, 256 bit key sizes] CCM, GCM, XTS Triple-DES ECB, CBC, CFB (64bit) and OFB Certificate #988 (64 bit) DH Non-Approved (Allowed in FIPS mode) DSA Certificate #464 Dual EC DRBG (SP800-90) Certificate #57 EC-Diffie-Hellman, Non-Approved (Allowed in FIPS mode) EC-Diffie-Hellman with Cofactor EC-DSA, EC-DSA-SHA1 Certificate #182 FIPS 186-2 PRNG Certificate #802 (Change Notice 1-with and without the mod q step) HMAC DRBG (SP800-90) Certificate #57 HMAC-SHA1, SHA224, SHA256, SHA384, Certificate #863 SHA512 RSA encrypt/decrypt Non-Approved (Allowed in FIPS mode for key transport) RSA X9.31, PKCS #1 V.1.5, PKC S#1 V.2.1 Certificate #717 (SHA256 - PSS) SHA-1 Certificate #1328 SHA-224, 256, 384, 512 Certificate #1328 Crypto-J Cryptographic Toolkit 15 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services The following are the non-FIPS 140-approved algorithms provided by Crypto-J, when operating in NON_FIPS140_MODE. • DES • DESX • ECAES • ECIES • MD2 • MD5 • PBE • Random Number Generators (ANSI X9.31 (non-compliant), MD5Random and SHA1Random) RC2® block cipher • RC4® stream cipher • RC5® block cipher • • PBE with SHA1 and Triple-DES • RSA OAEP for key transport • Raw RSA encryption and decryption • RSA Keypair Generation MultiPrime (2 or 3 primes) • RIPEMD160 • HMAC-MD5. 16 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.7 Self-tests Crypto-J performs power-up and conditional self-tests to ensure proper operation. If the power-up self-test fails, the toolkit is disabled and throws a SecurityException. The toolkit can only leave the disabled state by restarting the JVM. If the conditional self-test fails, the toolkit throws a SecurityException and aborts the operation. A conditional self test failure does NOT disable the toolkit. 1.7.1 Power-up Self-tests The following FIPS-140 required power-up self-tests are implemented in Crypto-J: • FIPS186 PRNG KAT • AES KAT • TDES KAT • SHA-1 KAT • SHA-224 KAT • SHA-256 KAT • SHA-384 KAT • SHA-512 KAT • HMAC SHA-1 KAT • HMAC SHA-224 KAT • HMAC SHA-256 KAT • HMAC SHA-384 KAT • HMAC SHA-512 KAT • HMAC DRBG Self-Test • ECDRBG Self-Test • ECDSA KAT • Software/firmware integrity check • DSA KAT • DSA, RSA, EC pair-wise consistency test • RSA (signature) KAT. The following non-FIPS-140 power-up self-tests are implemented in Crypto-J: • MD5 KAT • HMAC MD5 KAT • ECIES KAT • ECAES KAT. Power-up self-tests are executed automatically when Crypto-J is loaded into memory. Crypto-J Cryptographic Toolkit 17 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 1.7.2 Conditional Self-tests Crypto-J performs two conditional self-tests: • Pair-wise consistency tests each time the toolkit generates a DSA, RSA or EC public/private key pair. • Continuous RNG (CRNG) test each time the toolkit produces random data, as per the FIPS 186-2 standard. The CRNG test is performed on all approved and non-approved RNGs. 1.7.3 Mitigation of Other Attacks RSA key operations implement blinding by default. Blinding is a reversible way of modifying the input data, so as to make the RSA operation immune to timing attacks. Blinding has no effect on the algorithm other than to mitigate attacks on the algorithm. RSA Blinding is implemented through blinding modes, for which the following options are available: • Blinding mode off • Blinding mode with no update, where the blinding value is squared for each operation • Blinding mode with full update, where a new blinding value is used for each operation. 18 Crypto-J Cryptographic Toolkit RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 2 Secure Operation of Crypto-J The following guidance must be followed in order to operate the Crypto-J module in a FIPS 140 mode of operation, in conformance with FIPS 140-2 requirements. 2.1 Module Configuration To operate the Crypto-J module in compliance with FIPS 140-2 requirements, the com.rsa.cryptoj.kat.strategy Java security property must be set to the value on.load at start-up of the module. See the RSA BSAFE Crypto-J Installation Guide for more information about setting this property. The property is read once only, on start-up, and any subsequent changes to the property are ignored. Setting this property ensures that all module self-tests are run during module start-up, as specified by FIPS 140-2 requirements. If any self-test fails, the module is disabled. 2.2 Security Roles, Authentication, and Services Operation To operate the cryptographic module in FIPS 140 Security Level 1 Roles, Authentication, and Services mode, ensure that the Java Security property com.rsa.cryptoj.fips140auth in the /lib/security/java.security file is NOT set. That is, ensure that the property does not exist in the java.security file. No role authentication is required for operation of the module in Security Level 1 mode. When in Security Level 1 mode, invocation of methods which are particular to Security Level 2 Roles, Authentication and Services will result in an error. These methods include constructors for FIPS140Context objects which accept a PIN, as well as PIN management APIs on the CryptoJ class. Secure Operation of Crypto-J 19 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 2.3 Crypto User Guidance This section provides guidance to the toolkit user to ensure that the toolkit is used in a FIPS 140-2 compliant way. Section 2.3.1 provides algorithm-specific guidance. The requirements listed in this section are not enforced by the module and must be ensured by the module user. Section 2.3.2 provides guidance on obtaining assurances for Digital Signature Applications. Section 2.3.3 provides general crypto user guidance. 2.3.1 Crypto User Guidance on Algorithms • The Crypto User must only use algorithms approved for use in a FIPS 140 mode of operation, as listed in Table 4, “Crypto-J FIPS-approved Algorithms,” on page 15. • When using GCM feedback mode for symmetric encryption, the authentication tag length and authenticated data length may be specified as input parameters, but the Initialization Vector (IV) must not be specified. It must be generated internally. • RSA keys used for signing shall not be used for any other purpose other than digital signatures. • For RSASSA-PSS, the length of the salt (sLen) shall be 0<=sLen<=hlen where hlen is the length of the hash function output block. Bit lengths for the Diffie-Hellman1 key agreement must be between 1024 and • 2048 bits. Diffie Hellman shared secret provides between 80 bits and 112 bits of encryption strength. • Bit lengths for an HMAC key must be one half of the block size. • For RSA digital signature generation either Dual EC DRBG or HMACDRBG have to be used. • EC key pairs must have domain parameters from the set of NIST-recommended named curves (P192, P224, P256, P384, P521, B163, B233, B283, B409, B571, K163, K233, K283, K409, and K571). The domain parameters can be specified by name or can be explicitly defined. The module limits possible curves for Dual EC DRBG to P-256, P-384, and P-521 in accordance with SP 800-90. • EC Diffie-Hellman primitives must use curve domain parameters from the set of NIST recommended named curves listed above. The domain parameters can be specified by name, or can be explicitly defined. Using the NIST-recommended curves, the computed Diffie-Hellman shared secret provides between 80 bits and 256 bits of encryption strength. • When using an Approved RNG to generate keys or DSA parameters, the RNG’s requested security strength must be at least as great as the security strength of the key being generated. That means that either Dual EC DRBG or HMACDRBG 1 Using the minimum allowed modulus size, the minimum strength of encryption provided is 80 bits. 20 Secure Operation of Crypto-J RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services with an appropriate strength have to be used. For more information on requesting the RNG security strength, see the Random Number Generation sections of the RSA BSAFE Crypto-J Developer's Guide. • SHA1 is a FIPS approved hash algorithm for the generation of digital signatures only until the end of 2010. More information on the algorithm strength and keysize is provided in the RSA BSAFE Crypto-J Release Notes. 2.3.2 Crypto User Guidance on Obtaining Assurances for Digital Signature Applications Crypto-J 5.0 has added support for the FIPS 186-3 standard for digital signatures in FIPS 140-2 mode. The following gives an overview of the assurances required by FIPS 186-3. NIST Special Publication 800-89: “Recommendation for Obtaining Assurances for Digital Signature Applications” provides the methods to obtain these assurances. The tables below describes the FIPS 186-3 requirements for signatories and verifiers and the corresponding Crypto-J toolkit capabilities and recommendations. Table 5 Signatory Requirements FIPS 186-3 Requirement Crypto-J toolkit capabilities and recommendations Obtain appropriate DSA and ECSDSA The generation of DSA parameters is in accordance with the FIP parameters when using DSA or ECDSA. 186-3 standard for the generation of probable primes. For ECDSA, use the NIST recommended curves as defined in section 2.3.1. Obtain assurance of the validity of those The toolkit provides APIs to validate DSA parameters for probable parameters. primes as described in FIPS 186-3. For the JSAFE API, com.rsa.jsafe.JSAFE_VerifyPQG.verifyPQGParams() For the JCE API, com.rsa.jsafe.provider.Assurance.verifyDSAParame ters() For ECDSA, use the NIST recommended curves as defined in section 2.3.1. Obtain a digital signature key pair that is The toolkit generates the digital signature key pair according to the generated as specified for the appropriate required standards. digital signature algorithm. Choose a FIPS approved RNG like HMACDRBG or Dual-ECDRBG to generate the key pair. Obtain assurance of the validity of the The toolkit provides APIs to explicitly validate the public key public key. according to NIST Special Publication 800-89. For the JSAFE API, com.rsa.jsafe.JSAFE_VerifyPQG.verifyPQGParams() For the JCE API, com.rsa.jsafe.provider.Assurance. isValidPublicKey() Secure Operation of Crypto-J 21 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 5 Signatory Requirements (continued) FIPS 186-3 Requirement Crypto-J toolkit capabilities and recommendations Obtain assurance that the signatory The toolkit verifies the signature created using the private key, but actually possesses the associated private all other assurances are outside the scope of the toolkit. key. Table 6 Verifier Requirements FIPS 186-3 Requirement Crypto-J toolkit capabilities and recommendations Obtain assurance of the signatory's The toolkit verifies the signature created using the private key, but all claimed identity other assurances are outside the scope of the toolkit. Obtain assurance of the validity of the The toolkit provides APIs to validate DSA parameters for probable domain parameters for DSA and primes as described in FIPS 186-3. ECDSA. For the JSAFE API, com.rsa.jsafe.JSAFE_VerifyPQG.verifyPQGParams() For the JCE API, com.rsa.jsafe.provider.Assurance.verifyDSAParamete rs() For ECDSA, use the NIST recommended curves as defined in section 2.3.1. Obtain assurance of the validity of the The toolkit provides APIs to explicitly validate the public key public key according to NIST Special Publication 800-89. For the JSAFE API, com.rsa.jsafe.JSAFE_VerifyPQG.verifyPQGParams() For the JCE API, com.rsa.jsafe.provider.Assurance. isValidPublicKey() Obtain assurance that the claimed Outside the scope of the toolkit. signatory actually possessed the private key that was used to generate the digital signature at the time that the signature was generated For more details on the requirements, see the FIPS 186-3 and NIST Special Publication 800-89. 2.3.3 General Crypto User Guidance Crypto-J users should take care to zeroize CSPs when they are no longer needed. For more information on clearing sensitive data, see Clearing Sensitive Data in the RSA BSAFE Crypto-J Developer's Guide. 22 Secure Operation of Crypto-J RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 2.4 Crypto Officer Guidance The Crypto Officer is responsible for installing the toolkit. Installation instructions are provided in the RSA BSAFE Crypto-J Installation Guide. 2.5 Role Changes If a user of Crypto-J needs to operate the toolkit in different roles, then the user must ensure that all instantiated cryptographic objects are destroyed before changing from the Crypto User role to the Crypto Officer role, or unexpected results could occur. 2.6 Operating the Cryptographic Module The Cryptographic Module operates in FIPS140_MODE by default after module power-up. The initial mode can be configured through the use of the com.rsa.cryptoj.fips140initialmode security property. See the RSA BSAFE Crypto-J Installation Guide for details on how to set this property. If the property is not set, then the default mode FIPS140_MODE is used. The current mode of the cryptographic module can be determined with a call to the CryptoJ.getMode() method. The mode of the cryptographic module can be changed by using the function CryptoJ.setMode() with an information identifier from Table 7, “Mode of Operation Values,” on page 24. When changing to an approved mode of operation, the toolkit causes the power-up self-tests to run. After setting the cryptographic module into a FIPS approved mode, the Cryptographic Module ensures that only the FIPS approved algorithms listed in “Services” on page 8 are available to operators. To disable FIPS mode, call the CryptoJ.setMode() method with the mode identifier NON_FIPS140_MODE. The Service CryptoJ.runSelfTests() is restricted to operation by the Crypto Officer. Secure Operation of Crypto-J 23 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 2.7 Modes of Operation There are five modes of operation: • FIPS140_MODE • FIPS140_SSL_MODE • NON_FIPS140_MODE • FIPS140_ECC_MODE • FIPS140_SSL_ECC_MODE. The following table lists the values that can be used in the setMode() method to change the mode of operation, and the algorithms available in that mode. Table 7 Mode of Operation Values Value Algorithms Available Provides the cryptographic algorithms listed inTable 4, “Crypto-J CryptoJ.FIPS140_MODE FIPS 140-2 approved. FIPS-approved Algorithms,” on page 15. This is the Crypto-J default mode on start up. Provides the same algorithms as CryptoJ.FIPS140_MODE, plus CryptoJ.FIPS140_SSL_MODE FIPS 140-2 approved if used with TLS the MD5 message digest. protocol implementations. This mode can be used in the context of the key establishment phase in the TLSv1, TLSv1.1 and TLSv1.2 protocols. For more information, see section 7.1 Acceptable Key Establishment Protocols in Implementation Guidance for FIPS PUB 140-2 and the Cryptographic Module Validation Program. The implementation guidance disallows the use of the SSLv2 and SSLv3 versions. Cipher suites that include non-FIPS 140-2-approved algorithms are unavailable. This mode allows implementations of the TLS protocol to operate Crypto-J in a FIPS 140-2-compliant manner. Allows users to operate Crypto-J without any cryptographic CryptoJ.NON_FIPS140_MODE Not FIPS 140-2 approved. algorithm restrictions. Provides the same algorithms as CryptoJ.FIPS140_MODE, plus CryptoJ.FIPS140_ECC_MODE Not FIPS 140-2 approved. ECAES and ECIES. Provides the same algorithms as CryptoJ.FIPS140_SSL_MODE, CryptoJ.FIPS140_SSL_ECC_MODE Not FIPS 140-2 approved. plus ECAES and ECIES. The same restrictions with respect to protocol versions and cipher suites as in CryptoJ.FIPS140_SSL_MODE apply. Note: Refer to Random Number Generator for details of the default random number generator for the available algorithms. 24 Secure Operation of Crypto-J RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Cryptographic algorithms can be created in different modes using the com.rsa.jsafe.crypto.FIPS140Context class for the JSAFE API. For more information about operating in FIPS 140 mode, see the RSA BSAFE Crypto-J JSAFE and JCE Software Module 5.0 Developers Guide. 2.8 Random Number Generator Crypto-J provides a default RNG. This default RNG can be set to one of the FIPS-140 approved RNG, (ECDRBG, HMACDRBG, FIPS186-2 RNG) using the property com.rsa.crypto.default.random. For the correct configuration settings, see the RSA BSAFE Crypto-J Developer's Guide. If the property is not set, the default RNG used is Dual ECDRBG. Users in FIPS 140-2 mode can select either the FIPS 186-2, ECDRBG or HMAC DRBG when creating a RNG object and setting this object against the operation requiring random number generation (for example key generation). Users in non-FIPS 140-2 mode can use any RNG and set it against the operation requiring random number generation. For more information on each function, see the RSA BSAFE Crypto-J Developer's Guide Secure Operation of Crypto-J 25 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services 3 Acronyms The following table lists the acronyms used with Crypto-J and their definitions. Table 8 Acronyms used with Crypto-J Acronym Definition 3DES Refer to Triple-DES AES Advanced Encryption Standard. A fast block cipher with a 128-bit block, and keys of lengths 128, 192 and 256 bits. This will replace DES as the US symmetric encryption standard. API Application Programming Interface. Attack Either a successful or unsuccessful attempt at breaking part or all of a cryptosystem. Attack types include an algebraic attack, birthday attack, brute force attack, chosen ciphertext attack, chosen plaintext attack, differential cryptanalysis, known plaintext attack, linear cryptanalysis, middleperson attack and timing attack. CBC Cipher Block Chaining. A mode of encryption in which each ciphertext depends upon all previous ciphertexts. Changing the IV alters the ciphertext produced by successive encryptions of an identical plaintext. CFB Cipher Feedback. A mode of encryption that produces a stream of ciphertext bits rather than a succession of blocks. In other respects, it has similar properties to the CBC mode of operation. CRNG Continuous Random Number Generation. CSP Critical Security Parameters. DES Data Encryption Standard. A symmetric encryption algorithm with a 56-bit key. Diffie-Hellman The Diffie-Hellman asymmetric key exchange algorithm. There are many variants, but typically two entities exchange some public information (for example, public keys or random values) and combines them with their own private keys to generate a shared session key. As private keys are not transmitted, eavesdroppers are not privy to all of the information that composes the session key. DRBG Deterministic Random Bit Generator. DSA Digital Signature Algorithm. An asymmetric algorithm for creating digital signatures. EC Elliptic Curve. ECAES Elliptic Curve Asymmetric Encryption Scheme. 26 Acronyms RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 8 Acronyms used with Crypto-J (continued) Acronym Definition ECB Electronic Code Book. A mode of encryption in which identical plaintexts are encrypted to identical ciphertexts, given the same key. ECC Elliptic Curve Cryptography. ECDH Elliptic Curve Diffie-Hellman. ECDHC Elliptic Curve Diffie-Hellman with Components. ECDSA Elliptic Curve Digital Signature Algorithm. ECIES Elliptic Curve Integrated Encryption Scheme. Encryption The transformation of plaintext into an apparently less readable form (called ciphertext) through a mathematical process. The ciphertext may be read by anyone who has the key that decrypts (undoes the encryption) the ciphertext. FIPS Federal Information Processing Standards. HMAC Keyed-Hashing for Message Authentication Code. IV Initialization Vector. Used as a seed value for an encryption operation. JCE Java Cryptography Extension. JVM Java Virtual Machine. KAT Known Answer Test. Key A string of bits used in cryptography, allowing people to encrypt and decrypt data. Can be used to perform other mathematical operations as well. Given a cipher, a key determines the mapping of the plaintext to the ciphertext. Various types of keys include: distributed key, private key, public key, secret key, session key, shared key, subkey, symmetric key, and weak key. MD5 A secure hash algorithm created by Ron Rivest. MD5 hashes an arbitrary-length input into a 16-byte digest. NIST National Institute of Standards and Technology. A division of the US Department of Commerce (formerly known as the NBS) which produces security and cryptography-related standards. OFB Output Feedback. A mode of encryption in which the cipher is decoupled from its ciphertext. OS Operating System. PC Personal Computer. Acronyms 27 RSA BSAFE Crypto-J 5.0 Security Policy Level 1 - Roles, Authentication and Services Table 8 Acronyms used with Crypto-J (continued) Acronym Definition private key The secret key in public key cryptography. Primarily used for decryption but also used for encryption with digital signatures. PRNG Pseudo-random Number Generator. RC2 Block cipher developed by Ron Rivest as an alternative to the DES. It has a block size of 64 bits and a variable key size. It is a legacy cipher and RC5 should be used in preference. RC4 Symmetric algorithm designed by Ron Rivest using variable length keys (usually 40 bit or 128 bit). RC5 Block cipher designed by Ron Rivest. It is parameterizable in its word size, key length and number of rounds. Typical use involves a block size of 64 bits, a key size of 128 bits and either 16 or 20 iterations of its round function. RNG Random Number Generator. RSA Public key (asymmetric) algorithm providing the ability to encrypt data and create and verify digital signatures. RSA stands for Rivest, Shamir, and Adleman, the developers of the RSA public key cryptosystem. SHA Secure Hash Algorithm. An algorithm which creates a hash value for each possible input. SHA takes an arbitrary input which is hashed into a 160-bit digest. SHA-1 A revision to SHA to correct a weakness. It produces 160-bit digests. SHA-1 takes an arbitrary input which is hashed into a 20-byte digest. SHA-2 The NIST-mandated successor to SHA-1, to complement the Advanced Encryption Standard. It is a family of hash algorithms (SHA-256, SHA-384 and SHA-512) which produce digests of 256, 384 and 512 bits respectively. TDES Refer to Triple-DES Triple-DES A symmetric encryption algorithm which uses either two or three DES keys. The two key variant of the algorithm provides 80 bits of security strength while the three key variant provides 112 bits of security strength. 28 Acronyms