Bomgar Corporation B200™ and B300™ Remote Support Appliances Firmware Version: 3.2.2FIPS; Software Version: 10.6.2FIPS FIPS 140-2 Non-Proprietary Security Policy FIPS Security Level: 2 Document Version: 0.8 Prepared for: Prepared by: Bomgar Corporation Corsec Security, Inc. 578 Highland Colony Parkway 13135 Lee Jackson Memorial Highway Paragon Centre, Suite 300 Suite 220 Ridgeland, MS 39157 Fairfax, VA 22033 United States of America United States of America Phone: +1 (601) 519-0123 Phone: +1 (703) 267-6050 http://www.bomgar.com http://www.corsec.com Security Policy, Version 0.8 August 11, 2011 Table of Contents 1 INTRODUCTION ................................................................................................................... 4 1.1 PURPOSE ................................................................................................................................................................ 4 1.2 REFERENCES .......................................................................................................................................................... 4 1.3 DOCUMENT ORGANIZATION ............................................................................................................................ 4 2 B200™ AND B300™ REMOTE SUPPORT APPLIANCES .................................................. 5 2.1 OVERVIEW ............................................................................................................................................................. 5 2.2 MODULES SPECIFICATION ................................................................................................................................... 7 2.3 MODULE INTERFACES .......................................................................................................................................... 8 2.4 ROLES AND SERVICES .........................................................................................................................................11 2.4.1 Crypto-Officer Role.............................................................................................................................................. 11 2.4.2 Instance-Admin Role ........................................................................................................................................... 11 2.4.3 Instance-User Role .............................................................................................................................................. 11 2.4.4 Services ................................................................................................................................................................... 11 2.4.5 Unauthenticated Operator Services .............................................................................................................. 13 2.4.6 Authentication Mechanism ............................................................................................................................... 13 2.5 PHYSICAL SECURITY ...........................................................................................................................................13 2.6 OPERATIONAL ENVIRONMENT.........................................................................................................................13 2.7 CRYPTOGRAPHIC KEY MANAGEMENT ............................................................................................................13 2.8 EMI/EMC ............................................................................................................................................................15 2.9 SELF-TESTS ..........................................................................................................................................................16 2.9.1 Power-Up Self-Tests ............................................................................................................................................ 16 2.9.2 Conditional Self-Tests ......................................................................................................................................... 16 2.10 MITIGATION OF OTHER ATTACKS ..................................................................................................................16 3 SECURE OPERATION ......................................................................................................... 17 3.1 INITIAL SETUP......................................................................................................................................................17 3.1.1 B200 Hardware Setup ...................................................................................................................................... 17 3.1.2 B200 Label Inspection ....................................................................................................................................... 17 3.1.3 B300 Hardware Setup ...................................................................................................................................... 18 3.1.4 B300 Label Inspection and Application ....................................................................................................... 19 3.1.5 Firmware/Software Version Verification ....................................................................................................... 22 3.2 FIPS MODE COMPLIANCE .................................................................................................................................22 3.3 CRYPTO-OFFICER GUIDANCE ..........................................................................................................................25 3.3.1 Management ........................................................................................................................................................ 25 3.3.2 Status Monitoring ................................................................................................................................................ 25 3.3.3 Zeroization ............................................................................................................................................................ 26 3.4 INSTANCE-ADMIN AND INSTANCE-USER GUIDANCE...................................................................................26 4 ACRONYMS .......................................................................................................................... 27 Table of Figures FIGURE 1 – BOMGAR B200 (TOP) AND B300 (BOTTOM) ...................................................................................................5 FIGURE 2 – TYPICAL DEPLOYMENT.........................................................................................................................................6 FIGURE 3 – BLOCK DIAGRAM FOR B200 WITH CRYPTOGRAPHIC BOUNDARY ...............................................................7 FIGURE 4 – BLOCK DIAGRAM FOR B300 WITH CRYPTOGRAPHIC BOUNDARY................................................................8 FIGURE 5 – FRONT AND REAR VIEW OF B200......................................................................................................................9 FIGURE 6 – FRONT AND REAR VIEW OF B300......................................................................................................................9 FIGURE 7 – TAMPER SEAL APPLIED TO THE TOP, OVERLAPPING THE GALVANIZED METAL COVER AND THE FRONT PANEL.............................................................................................................................................................................. 18 FIGURE 8 – TAMPER SEAL APPLIED TO THE REAR, OVERLAPPING THE GALVANIZED METAL COVER AND REAR STEEL BEZEL............................................................................................................................................................................... 18 Bomgar B200™ and B300™ Remote Support Appliances Page 2 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 FIGURE 9 – REAR METALLIC BEZEL SEAL (LEFT) AND SEALED TOP COVER (RIGHT) ....................................................... 20 FIGURE 10 – SEALED FRONT BEZEL TO CHASSIS TOP (LEFT) AND SEALED FRONT BEZEL TO CHASSIS BOTTOM (RIGHT) .......................................................................................................................................................................... 20 FIGURE 11– SEALED TOP CHASSIS TO LEFT POWER SUPPLY (LEFT) AND SEALED TOP CHASSIS TO RIGHT POWER SUPPLY (RIGHT) ............................................................................................................................................................. 20 FIGURE 12 – IP CONFIGURATION PAGE ............................................................................................................................. 21 FIGURE 13 – SSL CONFIGURATION PAGE .......................................................................................................................... 22 FIGURE 14 – STATUS BASICS PAGE ...................................................................................................................................... 23 FIGURE 15 – ADVANCED SUPPORT PAGE ........................................................................................................................... 24 FIGURE 16 – SECURITY PAGE ................................................................................................................................................ 24 FIGURE 17 – SUPPORT PAGE ................................................................................................................................................. 25 List of Tables TABLE 1 – SECURITY LEVEL PER FIPS 140-2 SECTION ..........................................................................................................6 TABLE 2 – PHYSICAL PORTS AND LOGICAL INTERFACES .....................................................................................................9 TABLE 3 – LED DESCRIPTIONS............................................................................................................................................. 10 TABLE 4 – MAPPING OF AUTHENTICATED OPERATOR SERVICES TO INPUTS, OUTPUTS, CSPS, AND TYPE OF ACCESS ........................................................................................................................................................................... 11 TABLE 5 – UNAUTHENTICATED OPERATOR SERVICE ....................................................................................................... 13 TABLE 6 – AUTHENTICATION MECHANISM USED BY THE MODULES ............................................................................. 13 TABLE 7 – FIPS-APPROVED ALGORITHM IMPLEMENTATIONS .......................................................................................... 14 TABLE 8 – LIST OF CRYPTOGRAPHIC KEYS, CRYPTOGRAPHIC KEY COMPONENTS, AND CSPS................................. 15 TABLE 9 – ACRONYMS .......................................................................................................................................................... 27 Bomgar B200™ and B300™ Remote Support Appliances Page 3 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 1 Introduction 1.1 Purpose This is a non-proprietary Cryptographic Module Security Policy for the B200™ and B300™ Remote Support Appliances from Bomgar Corporation. This Security Policy describes how the B200™ and B300™ Remote Support Appliances meet the security requirements of FIPS1 140-2 and how to run the modules in a secure FIPS 140-2 mode. This policy was prepared as part of the Level 2 FIPS 140-2 validation of the modules. FIPS 140-2 – Security Requirements for Cryptographic Modules details the U.S. and Canadian Government requirements for cryptographic modules. More information about the FIPS 140-2 standard and validation program is available on the Cryptographic Module Validation Program (CMVP) website, which is maintained by the National Institute of Standards and Technology (NIST) and the Communication Security Establishment Canada (CSEC): http://csrc.nist.gov/groups/STM/cmvp. The B200™ and B300™ Remote Support Appliances are referred to in this document as Bomgar appliances, the cryptographic modules, or the modules. 1.2 References This document deals only with operations and capabilities of the modules in the technical terms of a FIPS 140-2 cryptographic module security policy. More information is available on the modules from the following sources:  The Bomgar website (http://www.bomgar.com/fips) contains information on the full line of products from Bomgar Corporation.  The CMVP website (http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/140val-all.htm) contains contact information for individuals to answer technical or sales-related questions for the modules. 1.3 Document Organization The Security Policy document is one document in a FIPS 140-2 Submission Package. In addition to this document, the Submission Package contains:  Vendor Evidence document  Finite State Model  Other supporting documentation as additional references This Security Policy and the other validation submission documentation were produced by Corsec Security, Inc. under contract to Bomgar Corporation. With the exception of this Non-Proprietary Security Policy, the FIPS 140-2 Validation Documentation is proprietary to Bomgar Corporation and is releasable only under appropriate non-disclosure agreements. For access to these documents, please contact Bomgar Corporation. FIPS – Federal Information Processing Standard 1 Bomgar B200™ and B300™ Remote Support Appliances Page 4 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 2 B200™ and B300™ Remote Support Appliances 2.1 Overview Bomgar Corporation specializes in appliance-based solutions for remote support. Their remote support appliances give support technicians secure remote control of computers over the Internet, LAN2, or WAN3. The software works through firewalls with no pre-installed client on the remote computer. With the Bomgar Remote Support Appliances, a support technician can see the screen and control the system virtually as if physically present. Figure 1 – Bomgar B200 (top) and B300 (bottom) The B200™ and B300™ Remote Support Appliances (shown in Figure 1 above) enable the use of remote support in multiple areas of an organization in a way that is secure, integrated and manageable. The Bomgar appliances can integrate with LDAP 4 for secure user management, prevent sensitive data from being routed outside the organization, and support extensive auditing and recording of support sessions. The logging is performed by the Bomgar appliances, which allows for the review of all Customer and Support Representative interactions, including playback of all desktop screen data. The appliances also integrate with leading systems management and identity management solutions and include an Application Programming Interface (API) for deeper integration. With Bomgar, support managers can create support teams, customize queues, and report on all support activities. Network administrators can also monitor the Bomgar appliances using Simple Network Management Protocol (SNMP). The Bomgar appliances enable remote access to multiple common operating systems, including various Linux distributions. They also enable remote control of various kinds of systems, including laptops, desktops, servers, kiosks, point-of-sale systems, smartphones, and network devices. The Bomgar appliances can work over internal and extended networks and can be internet-accessible. This allows support organizations to reduce less effective means of support by driving requests through custom support portals hosted on the appliances. The Bomgar appliances can route support requests to the appropriate technician or team and mediate connections between Customers and Support Representatives, allowing chat sessions, file downloads/uploads, screen-sharing, remote control of desktops, and access to system and diagnostic information. To enable the functionality described above, Bomgar has implemented architecture that places the Bomgar appliances at the center of all communications (see Figure 2 below for a typical deployment scenario). The Bomgar appliances provide a platform upon which one or more support sites are constructed. Sites represent individual help centers, and multiple sites can be set up to support multiple departments or groups LAN – Local Area Network 2 WAN – Wide Area Network 3 LDAP – Lightweight Directory Access Protocol 4 Bomgar B200™ and B300™ Remote Support Appliances Page 5 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 in a company. Each site would offer a web site interface using Hypertext Transfer Protocol (HTTP) for unauthenticated services and HTTP over TLS5 (HTTPS) for authenticated services, in addition to accepting direct client connections over a protocol running on top of TLS. Figure 2 – Typical Deployment6 The Bomgar appliances have two primary components that provide the appliances’ functionality. The first is the Firmware that provides system-level configuration of Bomgar appliances. Settings such as IP7 addresses and SSL/TLS configuration are all configured via the Firmware interface. The second component is made up of the software that provides site-level configuration, as well as the software clients that users interact with. The web interface behind the /login page is part of the software, as are the Representative Console, Customer Client, Connection Agent, and all other clients which are downloadable from the Bomgar appliances. The B200™ and B300™ Remote Support Appliances are validated at the following FIPS 140-2 Section levels: Table 1 – Security Level per FIPS 140-2 Section Section Section Title Level 1 Cryptographic Modules Specification 2 2 Cryptographic Modules Ports and Interfaces 2 3 Roles, Services, and Authentication 2 4 Finite State Model 2 5 Physical Security 2 N/A8 6 Operational Environment 7 Cryptographic Key Management 2 9 8 EMI/EMC 2 TLS – Transport Layer Security 5 Rep – Representative; SSL – Secure Socket Layer; DMZ – Demilitarized Zone; POS – Point of Sale; AD – Active Directory 6 IP – Internet Protocol 7 N/A – Not applicable 8 Bomgar B200™ and B300™ Remote Support Appliances Page 6 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Section Section Title Level 9 Self-tests 2 10 Design Assurance 2 11 Mitigation of Other Attacks N/A 2.2 Modules Specification The B200™ and B300™ Remote Support Appliances (running Firmware version 3.2.2FIPS and Software version 10.6.2FIPS) are multi-chip standalone modules that meet overall Level 2 FIPS 140-2 requirements. Physically, the modules are composed of the components of a standard server platform. Figure 3 and Figure 4 show a block diagram for the B200 and B300 respectively and identify the various components, connections, and information flows. The cryptographic boundary of the modules (denoted by the dotted lines in Figure 3 and Figure 4) is defined by the outer case of each appliance, which surrounds the complete set of hardware, firmware, and software components. Note that, though Figure 4 shows a single hard disk, the B300 can support up to four hard disks to support RAID10 functionality. Additionally, please note that the B300 power supply is not included the within the cryptographic boundary. Physical Cryptographic Boundary DVD Hardware RAM Network Management HDD Clock Generator SCSI/SATA Controller North Bridge Serial CPU(s) Audio South Bridge Cache PCI/PCIe Slots USB Power PCI/PCIe Graphics Supply Slots BIOS Controller Connector KEY: BIOS – Basic Input/Output System PCIe – PCI express CPU – Central Processing Unit HDD – Hard Disk Drive SATA – Serial Advanced Technology Attachment DVD – Digital Video Disc SCSI – Small Computer System Interface USB – Universal Serial Bus PCI – Peripheral Component Interconnect RAM – Random Access Memory Figure 3 – Block Diagram for B200 with Cryptographic Boundary EMI/EMC – Electromagnetic Interference / Electromagnetic Compatibility 9 RAID – Redundant Array of Independent Disks 10 Bomgar B200™ and B300™ Remote Support Appliances Page 7 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Physical Cryptographic Boundary DVD Hardware RAM Network Management HDD Clock Generator SCSI/SATA Controller North Bridge Serial CPU(s) Audio South Bridge Cache PCI/PCIe Slots USB PCI/PCIe Power Graphics Slots Interface BIOS Controller External Power Supply KEY: BIOS – Basic Input/Output System PCIe – PCI express CPU – Central Processing Unit HDD – Hard Disk Drive SATA – Serial Advanced Technology Attachment DVD – Digital Video Disc SCSI – Small Computer System Interface USB – Universal Serial Bus PCI – Peripheral Component Interconnect RAM – Random Access Memory Figure 4 – Block diagram for B300 with Cryptographic Boundary 2.3 Module Interfaces The modules’ design separates the physical ports into four logically distinct and isolated categories. They are:  Data Input  Data Output  Control Input  Status Output In addition, the modules receive power via a defined power input interface. Data input/output are the network data packets utilizing the services provided by the modules. These packets enter and exit the modules through the network ports. Control input consists of both configuration and administration data entering the modules through the web interface and also the input for the power and reset buttons. Status output consists of status information relayed via the LED 11 indicators and the web interface. LED – Light Emitting Diode 11 Bomgar B200™ and B300™ Remote Support Appliances Page 8 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 The physical ports and interfaces of the modules are depicted in Figure 5 and Figure 6 below. Figure 5 – Front and Rear View of B200 Figure 6 – Front and Rear View of B300 Of the ports and interfaces depicted in the figures above, only the following are enabled to be used in FIPS mode of operation:  Network ports  Power button  Reset button  Power connectors  LEDs Table 2 lists the physical interfaces available in the Bomgar appliances and also provides the mapping from the physical interfaces to logical interfaces as defined by FIPS 140-2. Table 2 – Physical Ports and Logical Interfaces FIPS 140-2 Logical Physical Port (B200) Physical Port (B300) Interface Data Input Network ports Network ports Data Output Network ports Network ports Bomgar B200™ and B300™ Remote Support Appliances Page 9 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 FIPS 140-2 Logical Physical Port (B200) Physical Port (B300) Interface Network ports, power button, Network ports, power button, Control Input reset switch reset switch Status Output LEDs, network ports LEDs, network ports Power Input Power connector Power connectors The cryptographic modules have a number of LEDs which indicate the state of the modules. The descriptions for the LEDs are listed in Table 3 for each module. Table 3 – LED Descriptions Model LED Condition Description On System on Power Off System off On IDE channel activity Hard Disk Drive SAS/SATA drive or DVD-ROM drive Blink (HDD) activity Off No HDD activity B200 On Linked LAN1/LAN2 Blink Network activity Off Disconnected On System overheat condition Overheat/Fan Blink Fan failure Off System normal On System on Power Off System off Blink HDD activity HDD Off No HDD activity On Linked LAN1/LAN2 Blink Network activity B300 Off Disconnected On System overheat condition Overheat/Fan Blink Fan failure Off System normal Fast Blink Red (1x/ Fan fail Universal sec) Information Solid Red CPU overheat Bomgar B200™ and B300™ Remote Support Appliances Page 10 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Model LED Condition Description Slow Blink Red (1x/ Power fail 4 sec) Local Unit Identifier (UID) button Solid Blue depressed 2.4 Roles and Services As required by FIPS 140-2, the module supports a Crypto-Officer (CO) role and a User role. The User role comprises an Instance-Admin role and an Instance-User role. The modules support role-based authentication for the Crypto-Officer and identity-based authentication for the Instance-Admin and Instance-User roles. Operators explicitly assume the role of Instance-Admin or Instance-User based on the authentication credentials used. The credentials used determine the services available to the operator. 2.4.1 Crypto-Officer Role The Crypto-Officer role is the administrator for the modules and is responsible for the initial setup and configuration. The Crypto-Officer has administrator rights to monitor and manage the firmware component’s configuration, manage the CO account, and reset the default Instance-Admin account passwords. 2.4.2 Instance-Admin Role The Instance-Admin has administrator rights to monitor and manage the software instance’s configuration, manage Instance-Admin accounts, and manage Instance-User accounts. 2.4.3 Instance-User Role The Instance-User can access the support services in the modules based on the permissions set by the Instance-Admin. The Instance-Admin has to grant access to Instance-Users to access services on the modules. 2.4.4 Services Services provided to authenticated operators are provided in Table 4 below. Please note that the keys and Critical Security Parameters (CSPs) listed indicate the type of access required:  Read: The CSP is read  Write: The CSP is established, generated, modified, or zeroized Table 4 – Mapping of Authenticated Operator Services to Inputs, Outputs, CSPs, and Type of Access Bomgar B200™ and B300™ Remote Support Appliances Page 11 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Service Description Operator Input Output CSP and Type of Access Manage Bomgar Configure IP12 and CO Command Command RSA public key – Read, Write appliance TLS settings response RSA private key – Read, Write settings Session Key – Read, Write PRNG13 seed – Read, Write CO Password – Read Manage CO Manage CO officer CO Command Command RSA public key – Read account account password response RSA private key – Read Session Key – Read, Write PRNG seed – Read, Write CO Password – Read, Write Reset Instance- Reset Instance- CO Command Command RSA public key – Read Admin Admin account response RSA private key – Read password password Session Key – Read, Write PRNG seed – Read, Write Instance-Admin Password – Write Configure Set up and CO, Command Command RSA public key – Read Instance-Admin monitor Instance- Instance- response RSA private key – Read accounts Admin accounts Admin Session Key – Read, Write PRNG seed – Read, Write Instance-Admin Password – Read, Write Configure Set up and Instance- Command Command RSA public key – Read Instance-User monitor Instance- Admin, response RSA private key – Read accounts User accounts Instance- Session Key – Read, Write User PRNG seed – Read, Write Instance-User Password – Read, Write Execute self- Perform power-up CO Command Command None tests self-tests on response demand Monitor status Monitor the status CO Command Status RSA public key – Read of the modules information RSA private key – Read Zeroize keys Zeroize plaintext CO Command Command All CSPs – Write keys response Perform Access and Instance- Command Command RSA public key – Read Representative perform services Admin, response RSA private key – Read Console service for Representative Instance- Session Key – Read, Write Consoles User PRNG seed – Read, Write Instance-Admin Password – Read Instance-User Password – Read Manage instance Manage instance Instance- Command Command RSA public key – Read settings configuration Admin, response RSA private key – Read settings Instance- Session Key – Read, Write User PRNG seed – Read, Write IP – Internet Protocol 12 PRNG – Pseudo Random Number Generator 13 Bomgar B200™ and B300™ Remote Support Appliances Page 12 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 2.4.5 Unauthenticated Operator Services The modules provide a service to unauthenticated operators as listed in Table 5 below. Table 5 – Unauthenticated Operator Service CSP and Type Service Description Input Output of Access Receive support Receive support services Command Command None service response 2.4.6 Authentication Mechanism The Crypto-Officer can access the modules remotely over a TLS session. The Crypto-Officer authenticates to the modules using a user ID and password. Instance-Admins and Instance-Users authenticate themselves with a user ID and password combination. Instance-Admins and Instance-Users can also authenticate to the modules via one of the following configurable methods: LDAP, Kerberos, or RADIUS. Table 6 lists the authentication mechanisms used by the modules. Table 6 – Authentication Mechanism Used by the Modules Authentication Type Strength Password Passwords are required to be at least 6 characters in length and can be a maximum of 64 characters in length. Numeric, alphabetic (upper and lower cases), and keyboard/extended characters can be used, for a total of 95 characters to choose from. A six-character password will yield a total of 956 = 735,091,890,625 possible combinations. 2.5 Physical Security The B200™ and B300™ Remote Support Appliances are multi-chip standalone cryptographic modules. Each is enclosed in a hard and opaque metal case that completely encloses all of the internal components of the module. Tamper-evident labels are applied to the cases to provide physical evidence of attempts to gain access to the modules’ internal components. All of the modules’ components are production grade. The placement of tamper-evident labels can be found in Section 3.1 of this document. 2.6 Operational Environment The operational environment requirements do not apply to the Bomgar appliances. The modules provide only a limited operational environment; they do not provide a general-purpose operating system environment. 2.7 Cryptographic Key Management The modules implement the FIPS-Approved algorithms listed in Table 7. Bomgar B200™ and B300™ Remote Support Appliances Page 13 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Table 7 – FIPS-Approved Algorithm Implementations B200 Certificate B300 Certificate Algorithm Number Number Advanced Encryption Standard (AES) in CBC14, ECB15, OFB16, and CFB17128 modes (with 128-bit, 192-bit, 1563 1563 and 256-bit keys) Triple Data Encryption Standard (TDES) – CBC, ECB, 1027 1027 OFB, CFB8, and CFB64 modes (with 2- and 3-key) RSA18 ANSI19 X9.31 (key generation) – 1024-, 1536-, 762 762 2048-bit RSA Public Key Cryptography Standard #1 (PKCS#1) 762 762 v1.5 (sign/verify) – 1024-, 2048-, 3072-, and 4096-bit RSA Probabilistic Signature Scheme (PSS) (sign/verify) 762 762 – 1024-, 2048-, 3072-, and 4096-bit Secure Hash Algorithm (SHA)-1, SHA-224, SHA-256, 1388 1388 SHA-384, and SHA-512 Keyed-Hash Message Authentication Code (HMAC) using SHA-1, SHA-224, SHA-256, SHA-384, and SHA- 915 915 512 ANSI X9.31 A.2.4 PRNG 844 844 The modules also support the following non-FIPS-Approved algorithms:  RSA key transport: 1024-, 1536-, 2048-, 3072-, 4096-bits (key wrapping; key establishment methodology provides between 80 and 150 bits of encryption strength)  RC420  RC4-40  DES  DES-40  MD521 The modules support the critical security parameters (CSPs) in Table 8. CBC – Cipher Block Chaining 14 ECB – Electronic Codebook 15 OFB – Output Feedback 16 CFB – Cipher Feedback 17 RSA – Rivest, Shamir, and Adleman 18 ANSI – American National Standards Institute 19 RC – Rivest Cipher 4 20 MD – Message Digest 5 21 Bomgar B200™ and B300™ Remote Support Appliances Page 14 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Table 8 – List of Cryptographic Keys, Cryptographic Key Components, and CSPs Generation CSP Type CSP Output Storage Zeroization Use / Input RSA 1024-, 1536-, Internally Exits only via Hard disk in By command or Key exchange private 2048-, 3072-, or generated or a secure TLS plaintext overwritten by for TLS sessions key 4096-bit RSA imported via session another key or by private key a secure TLS factory reset session RSA public 1024-, 1536-, Internally Exits in Hard disk in By command or Key exchange key 2048-, 3072-, or generated or plaintext plaintext overwritten by for TLS sessions 4096-bit RSA imported via form another key or by public key a secure TLS factory reset session  128-bit AES Session Internally Exits in Resides on By power cycle or Data encryption key generated encrypted volatile session and decryption CBC 128 key form during memory termination for TLS sessions  256-bit AES TLS only in CBC 128 key handshake plaintext  192-bit TDES CBC 112 key Crypto- 6-character Enters the Never exits Hard disk in Overwritten by Authenticates Officer minimum modules in the modules hashed form another password the CO password password encrypted or zeroized by form factory reset Instance- 6-character Enters the Never exits Hard disk in Overwritten by Authenticates Admin minimum modules in the modules hashed form another password the Instance- password password encrypted or zeroized by Admin form factory reset Instance- 6-character Enters the Never exits Hard disk in Overwritten by Authenticates User minimum modules in the modules hashed form another password the Instance- password password encrypted or zeroized by User form factory reset PRNG 32 bytes of Internally Never exits Resides on By power cycle, Seeds the FIPS- seed key random value generated the modules volatile session Approved memory termination, or PRNG only in factory reset plaintext PRNG 16 bytes of Internally Never exits Resides on By power cycle, Seeds the FIPS- seed random value generated the modules volatile session Approved memory termination, or PRNG only in factory reset plaintext 2.8 EMI/EMC The modules were tested and found conformant to the EMI/EMC requirements specified by 47 Code of Federal Regulations, Part 15, Subpart B, Unintentional Radiators, Digital Devices, Class A (i.e., for business use). Bomgar B200™ and B300™ Remote Support Appliances Page 15 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 2.9 Self-Tests 2.9.1 Power-Up Self-Tests The Bomgar appliances perform the following self-tests at power-up to verify the integrity of the software/firmware and the correct operation of the FIPS-Approved algorithm implementations employed by the modules:  Software/Firmware integrity check using a SHA-1 EDC22  AES Known Answer Test (KAT)  TDES KAT  RSA KATs (sign/verify and encrypt/decrypt)  HMAC KATs (SHA-1, SHA-224, SHA-256, SHA-384, and SHA-512)  SHA-1 KAT (note that all SHA-2 implementations are tested as part of the underlying mechanism of the HMAC SHA self-tests)  ANSI X9.31 PRNG KAT If any of the power-up self-tests fail, then the module enters an error state, logs the error to a file, and disables all cryptographic operations. 2.9.2 Conditional Self-Tests The Bomgar appliances perform the following conditional self-tests:  ANSI X9.31 A.2.4 PRNG Continuous RNG test: Verifying the correct operation of the PRNG algorithm implementation.  RSA pair-wise consistency check (sign/verify and encrypt/decrypt): Verifying that a newly generated RSA key pair works properly.  Software/Firmware load test: Verifying the upgrade packages. Upgrade packages are digitally- signed using RSA-4096, and are only loaded once the digital signature is verified. If any of the conditional self-tests fail, then the modules enter a soft error state until the error can be cleared. 2.10 Mitigation of Other Attacks This section is not applicable. The modules do not claim to mitigate any attacks beyond the FIPS 140-2 Level 2 requirements for this validation. EDC – Error Detection Code 22 Bomgar B200™ and B300™ Remote Support Appliances Page 16 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 3 Secure Operation The B200™ and B300™ Remote Support Appliances meet Level 2 requirements for FIPS 140-2. The sections below describe how to ensure that the modules are running securely. 3.1 Initial Setup The following sections provide the necessary step-by-step instructions for the secure hardware installation of the B200™ and B300™ Remote Support Appliances, as well as the steps necessary to configure the modules for FIPS-Approved mode of operation. If you have any questions or if issues arise at any point during the installation and configuration of your Bomgar appliances, contact the Bomgar support team toll- free at 1-877-826-6427 x2 or internationally at +01-601-519-0123 x2. 3.1.1 B200 Hardware Setup In order to set up the Bomgar B200, the following steps will need to be performed by the Crypto-Officer: 1. Inspect the tamper-evident labels as described in Section 3.1.2 below. The tamper evident labels shall be installed for the module to operate in a FIPS Approved mode of operation. 2. Follow the procedures included in the Hardware Setup Guide to install your B200 in your server rack. 3. After you have installed the Bomgar B200 per the Hardware Setup Guide, refer to the included Getting Started Guide and configure your network settings. Once the Bomgar B200’s network settings are correctly configured, return to Section 3.1.4.1 in 4. this document to configure your B200 for FIPS mode. 3.1.2 B200 Label Inspection The B200 will be shipped from the factory with all required labels pre-applied. Upon delivery, an authorized individual should ensure that the module was not tampered with during shipment and that the labels have been applied properly. . Also, tamper-evident labels shall be routinely inspected for damage by the Crypto-Officer, and replaced accordingly. Inspect all tamper-evident labels that shipped pre-applied to the B200 chassis (see Figure 7 and Figure 8), ensuring that each label shows no sign of tampering and is properly placed. Any attempt to reposition or remove the label will result in the voiding of that label and leave a residue on the surface. If you find a label that is questionable in appearance, contact Bomgar support toll-free at 1-877-826-6427 x2 or internationally at +01-601-519-0123 x2. Bomgar B200™ and B300™ Remote Support Appliances Page 17 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Pre-Applied Tamper Evident Label 1 Figure 7 – Tamper seal applied to the top, overlapping the galvanized metal cover and the front panel Pre-Applied Tamper Evident Label 2 Figure 8 – Tamper seal applied to the rear, overlapping the galvanized metal cover and rear steel bezel 3.1.3 B300 Hardware Setup In order to set up the Bomgar B300, the following steps will need to be performed by an authorized individual: 1. Unpack the Bomgar B300 and remove the front bezel from the front of the B300: a. Loosen the set screw on the right side of the front bezel. This screw keeps the tab in place during shipping. b. Press the tab on the right side of the front bezel and pull the front bezel towards you, right side first. Bomgar B200™ and B300™ Remote Support Appliances Page 18 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 2. Reseat the hard drives: a. Remove each of the hard drives by pressing the dark red buttons to unlatch the drive carrier handles. Use the handles to pull the drives about halfway out of the Bomgar chassis. b. As you reinsert each of the drives, the carrier handles will begin to close. Close the handles (you will feel them lock) and fully insert the drives into the B300 by firmly pressing on the left and right edges of the front of the drive carriers. Even if no movement is felt, this helps to ensure that the disk is completely engaged. 3. Reattach the B300’s front bezel: a. Engage the left side of the faceplate first, taking care to align the stubs of the faceplate with the drilled holes in the left ear. b. Repeat on the right side and then tighten the set screw. Take care not to over tighten this screw. 4. Inspect the tamper-evident labels as described in Section 3.1.4 below. The tamper evident labels shall be installed for the module to operate in a FIPS Approved mode of operation. If you find a label that is questionable in appearance, contact Bomgar support at 1-877-8-BOMGAR x2 or internationally at +01-601-519-0123 x2. 5. Follow the procedures included in the Hardware Setup Guide to install your B300 in your server rack. 6. After you have installed the Bomgar B300 per the Hardware Setup Guide, refer to the included Getting Started Guide and configure your network settings. 7. Once the Bomgar B300’s network settings are correctly configured, return to Section 3.1.4.1 in this document to configure your B300 for FIPS mode. 3.1.4 B300 Label Inspection and Application The B300 will be shipped from the factory with all required labels pre-applied except for the front bezel labels. This is to allow the end-user to reseat the drives upon receipt before affixing the front bezel to the appliance. Upon delivery, the Crypto-Officer should ensure that the module was not tampered with during shipment and that the labels have been applied properly. . Also, tamper-evident labels shall be routinely inspected for damage by the Crypto-Officer, and replaced accordingly. 1. Inspect all tamper-evident labels that shipped pre-applied to the Bomgar B300 chassis (see Figure 9), ensuring that each label shows no sign of tampering and is properly placed. Any attempt to reposition or remove the label will result in the voiding of that label and leave a residue on the surface. If you find a label that is questionable in appearance, contact Bomgar support toll-free at 1-877-826-6427 x2 or internationally at +01-601-519-0123 x2. 2. To apply the front bezel labels, first you must clean the top surface and front bezel of the B300 with isopropyl alcohol in the area where the tamper-evident labels will be placed. 3. Holding label by edges, place label on surface as indicated in the figures below. 4. Apply the included tamper-evident labels by rubbing gently across entire label to ensure adhesion to the surface. NOTE: Any attempt to reposition or remove the label will result in the voiding of that label and leave a residue on the surface. 5. Allow the labels to fully adhere to the B300 within 24 hours in a physically secure environment before placing it in the intended environment. Bomgar B200™ and B300™ Remote Support Appliances Page 19 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Pre-Applied Pre-Applied Tamper Tamper Evident Evident Label 2 Label 1 Figure 9 – Rear metallic bezel seal (Left) and Sealed top cover (Right) Tamper Tamper Evident Evident Label 4 Label 3 Figure 10 – Sealed front bezel to chassis top (Left) and Sealed front bezel to chassis bottom (Right) Tamper Evident Label 6 Tamper Evident Label 5 Figure 11– Sealed top chassis to left power supply (Left) and Sealed top chassis to right power supply (Right) Bomgar B200™ and B300™ Remote Support Appliances Page 20 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 3.1.4.1 B200 and B300 FIPS Mode Configuration Once all necessary initialization procedures have been performed as described in the preceding sections, the modules need to be configured to comply with FIPS 140-2 requirements. Once configured as described in this section, the modules will be considered to be in FIPS-Approved mode, which can be verified at any time by viewing the SSL Configuration page and ensuring it matches Figure 13 (NOTE: Figure 13 is identical for both the B200 and B300 with the exception of the heading). FIPS-Approved Mode Configuration Log into the Bomgar Appliance Administrative Interface (e.g. support.example.com/appliance) and configure your settings as described below23: 1. Navigate to the IP Configuration page under the Networking tab (see Figure 12 below). 2. Click the default 169.254.1.1 IP address to edit it. 3. Set the Telnet Server setting to Simplified. 4. Click the Save Changes button to commit these configuration changes. Figure 12 – IP Configuration Page 5. Navigate to the SSL Configuration page under the Security tab (see Figure 13 below). 6. Disable SSLv2 by ensuring that the Allow SSLv2 checkbox is cleared. 7. Disable SSLv3 by ensuring that the Allow SSLv3 checkbox is cleared 8. Ensure that only FIPS-Approved cipher suites are enabled: a. TLS_RSA_WITH_AES_128_CBC_SHA b. TLS_RSA_WITH_3DES_EDE_CBC_SHA 9. Click the Save button to commit these configuration changes. 23 NOTE: The module comes preloaded with a default password. The Crypto-Officer is responsible for changing this password before proceeding with the configuration steps. Bomgar B200™ and B300™ Remote Support Appliances Page 21 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Figure 13 – SSL Configuration Page 3.1.5 Firmware/Software Version Verification To ensure that the modules are running the validated versions of the module Firware and Software, operators should compare the running versions to those documented in this Security Policy. To obtain the version of the Firmware, an operator must visit the /appliance site, which is the interface used by the Crypto-Officer. To obtain the software version, an operator must visit the /login site, which requires the use of the credentials of the Instance-Admin role. Upon signing in, both display the "Status" page by default, showing the version number (“3.2.2fips (FIPS 140-2) (29180)” and “10.6.2fips (FIPS 140-2) (29326)”). 3.2 FIPS Mode Compliance Any time the modules deviate from the configuration detailed in Section 3.1.4.1 above, the modules will be considered to be in a non-FIPS-Approved mode of operation. Additionally, the guidance provided below must be followed to ensure that the modules remain in a FIPS- Approved mode of operation. Failure to do so will result in non-compliance. Bomgar B200™ and B300™ Remote Support Appliances Page 22 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011  When entering OR leaving FIPS-Approved mode, navigate to the Basics page under the Status tab of the /appliance interface and clear all existing CSPs by clicking the Reset Appliance to Factory Defaults button. NOTE: All Firmware and Software will be completely uninstalled after reset. Figure 14 – Status Basics Page  Never install software or firmware versions other than those listed on the cover page of this security policy. Only the software and firmware versions listed, are considered part of the validated configuration.  When using the module’s administrative interface, do not use the Advanced Support page under the Support tab of the /appliance interface. Doing so will result in non-compliance. Bomgar B200™ and B300™ Remote Support Appliances Page 23 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Figure 15 – Advanced Support Page  Enforce minimum password requirements for the Instance-Admin and Instance-User roles using the Security page under the Management tab. Figure 16 – Security Page  When using the management interface, do not use the Support page under the Management tab of the /login interface. Bomgar B200™ and B300™ Remote Support Appliances Page 24 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Figure 17 – Support Page  Never install a Bomgar software package via the Software Management page under the Management tab of the /login interface. Instead, ensure that any received Bomgar software packages are FIPS-Approved, and upload them from the Updates page under the Support tab of the administrative interface (e.g. support.example.com/appliance). You should always upload updates manually rather than using the auto-update feature. To maintain compliance, only the software update versions listed in this security policy are to be used. 3.3 Crypto-Officer Guidance The Crypto-Officer can initiate the execution of self-tests and can access the modules’ status reporting capability. Self-tests can be initiated at any time by power cycling the modules. 3.3.1 Management It is the responsibility of the Crypto-Officer to ensure that the modules are set up to run securely. Please refer to Section 3.2 for guidance that the Crypto-Officer must follow for the modules to be considered in a FIPS-Approved mode of operation. Additionally, the Crypto-Officers should be careful to protect any secret/private keys in their possession. For details regarding the management of the modules, please refer to the appropriate Bomgar appliance Administrative User’s Guide. 3.3.2 Status Monitoring Error message and status review is the responsibility of the Crypto-Officer. When any of the modules’ self-tests fail, the module reports an error message which can be viewed over a network connection. This connection is set using the IP Configuration page under the Networking tab as shown in Figure 12 in Section 3.1.4.1. Issuing the command "telnet [ip-address-assigned-to-network-port]" brings up the following options: 1. Show Error Message 2. Shutdown the Device 3. Reboot the Device Bomgar B200™ and B300™ Remote Support Appliances Page 25 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 4. Reset the Device to Factory Default 5. Done Issuing the Show Error Message command will display the reported error message. 3.3.3 Zeroization Session keys are zeroized at the termination of the session but are also cleared when the module is power- cycled. All other CSPs may be zeroized by either:  issuing the Reset Appliance to Factory Defaults command (found on the Basics page under the Status tab) and rebooting the module, or  selecting the Reset the Device to Factory Default option from a telnet session and rebooting the module. The zeroization of keys and CSPs is immediate, providing insufficient time for an attacker to compromise them. The Crypto-Officer must wait until the module has successfully rebooted in order to verify that zeroization has completed. 3.4 Instance-Admin and Instance-User Guidance The Instance-Admins do not have the ability to configure sensitive information on the modules, with the exception of the Instance-User and their own passwords. The Instance-Admin has the ability to configure the password strength policy for Instance-Admins and Instance-Users. Please refer to Section 3.2 above for guidance that should be followed for the modules to be considered in a FIPS-Approved mode of operation. Instance-Users do not have the ability to configure sensitive information on the modules, with the exception of their passwords. The Instance-Admins and Instance-Users shall employ strong passwords that meet or exceed the password strength requirements documented in Section 2.4.6 of this document, and must not reveal their passwords to anyone. Bomgar B200™ and B300™ Remote Support Appliances Page 26 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 4 Acronyms This section describes the acronyms used in this document. Table 9 – Acronyms Acronym Definition AD Active Directory AES Advanced Encryption Standard ANSI American National Standards Institute API Application Programming Interface CBC Cipher Block Chaining CFB Cipher Feedback CMVP Cryptographic Module Validation Program CO Crypto-Officer CSEC Communication Security Establishment Canada CSP Critical Security Parameter DMZ Demilitarized Zone ECB Electronic Codebook EDC Error Detection Code EMC Electromagnetic Compatibility EMI Electromagnetic Interference FIPS Federal Information Processing Standard HDD Hard Disk Drive HMAC (Keyed-) Hash Message Authentication Code HTTP Hypertext Transfer Protocol HTTPS Hypertext Transfer Protocol over TLS IP Internet Protocol IPMI Intelligent Platform Management Interface KAT Known Answer Test LAN Local Area Network LDAP Lightweight Directory Access Protocol LED Light Emitting Diode MD5 Message Digest 5 N/A Not Applicable NIST National Institute of Standards and Technology OFB Output Feedback Bomgar B200™ and B300™ Remote Support Appliances Page 27 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Security Policy, Version 0.8 August 11, 2011 Acronym Definition PCI Peripheral Component Interconnect PKCS Public Key Cryptography Standard POS Point of Sale PRNG Pseudo Random Number Generator PSS Probabilistic Signature Scheme RAID Redundant Array of Independent Disks RC4 Rivest Cipher 4 RNG Random Number Generator RSA Rivest, Shamir, and Adleman SHA Secure Hash Algorithm SNMP Simple Network Management Protocol SSL Secure Sockets Layer TDES Triple Data Encryption Standard TLS Transport Layer Security UID Unit Identifier USB Universal Serial Bus WAN Wide Area Network Bomgar B200™ and B300™ Remote Support Appliances Page 28 of 29 © 2011 Bomgar Corporation This document may be freely reproduced and distributed whole and intact including this copyright notice. Prepared by: Corsec Security, Inc. 13135 Lee Jackson Memorial Highway, Suite 220 Fairfax, VA 22033 United States of America Phone: +1 (703) 267-6050 Email: info@corsec.com http://www.corsec.com